Wifi

[barbaro00]

Hi,

I does not work for me...
The Kernel works well but no wifi...

did you look at dmesg output?

my guess is you need the bin file

http://www.atari-forum.com/viewtopic.ph ... 1u#p344349

Does not work

My dmesg:

[ 0.181167] usbcore: registered new interface driver rtl8192cu
[ 0.181284] usbcore: registered new interface driver rtl8xxxu
[ 0.181290] RTL871X: module init start
[ 0.181294] RTL871X: rtl8821au v4.3.14
[ 0.181298] RTL871X: rtl8821au BT-Coex version = BTCOEX20150128-51
[ 0.181377] usbcore: registered new interface driver rtl8821au
[ 0.181382] RTL871X: module init ret=0
[ 0.181386] RTW: module init start
[ 0.181391] RTW: rtl88x2bu v5.3.1_27678.20180430_COEX20180427-5959
[ 0.181394] RTW: build time: Feb 23 2019 18:30:12
[ 0.181397] RTW: rtl88x2bu BT-Coex version = COEX20180427-5959
[ 0.181430] RTW: rtw_inetaddr_notifier_register_22b
[ 0.181496] usbcore: registered new interface driver rtl88x2bu
[ 0.181502] RTW: module init ret=0
[ 0.181858] dwc2 ffb40000.usb: ffb40000.usb supply vusb_d not found, using dummy regulator
[ 0.181921] dwc2 ffb40000.usb: Linked as a consumer to regulator.0
[ 0.181933] dwc2 ffb40000.usb: ffb40000.usb supply vusb_a not found, using dummy regulator


It's another firmware???

[lavatar]

Hi All,

I am trying to get this working on my MiSTer and I ain't got a clue lol. It says its a RalinkWIFI



Can someone help me out please

If you go into console or SSH and type "dmesg" you should get some info, but at the very least, the USB vendor and product IDs which can be used to identify the specific Ralink chipset.

I have one similar, and dmesg report me this on infinite loop:

[ 95.533364] usb 1-1.2: new full-speed USB device number 10 using dwc2
[ 95.618458] usb 1-1.2: not running at top speed; connect to a high speed hub
[ 95.634141] usb 1-1.2: New USB device found, idVendor=148f, idProduct=7601, bcdDevice= 0.00
[ 95.634152] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 95.634159] usb 1-1.2: Product: 802.11 n WLAN
[ 95.634166] usb 1-1.2: Manufacturer: MediaTek
[ 95.634172] usb 1-1.2: SerialNumber: 1.0
[ 95.702367] usb 1-1.2: reset full-speed USB device number 10 using dwc2
[ 95.793446] mt7601u 1-1.2:1.0: ASIC revision: 76010001 MAC revision: 76010500
[ 95.804580] mt7601u 1-1.2:1.0: Firmware Version: 0.1.00 Build: 7640 Build time: 201302052146____
[ 96.435612] mt7601u 1-1.2:1.0: Warning: unsupported EEPROM version 0d
[ 96.435623] mt7601u 1-1.2:1.0: EEPROM ver:0d fae:00
[ 96.707194] mt7601u 1-1.2:1.0: Error: RX urb failed:-71
[ 96.712533] mt7601u 1-1.2:1.0: Error: RX urb failed:-71
[ 96.717827] mt7601u 1-1.2:1.0: Error: RX urb failed:-71
[ 96.723119] mt7601u 1-1.2:1.0: Error: RX urb failed:-71
[ 96.728414] mt7601u 1-1.2:1.0: Error: RX urb failed:-71
[ 96.733700] mt7601u 1-1.2:1.0: Error: RX urb failed:-71
[ 96.740122] mt7601u 1-1.2:1.0: Error: MCU resp urb failed:-71
[ 96.745877] mt7601u 1-1.2:1.0: Error: MCU resp evt:0 seq:5-4!
[ 96.751965] usb 1-1: USB disconnect, device number 5

Hello,

i have a similar Dongle.

This is my Log:

Code: Select all

[    0.188534] usb usb2: SerialNumber: vhci_hcd.0
[    0.189044] hub 2-0:1.0: USB hub found
[    0.189096] hub 2-0:1.0: 8 ports detected
[    0.190125] vhci_hcd vhci_hcd.0: USB/IP Virtual Host Controller
[    0.190140] vhci_hcd vhci_hcd.0: new USB bus registered, assigned bus number 3
[    0.190370] usb usb3: We don't know the algorithms for LPM for this host, disabling LPM.
[    0.190592] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19
[    0.190602] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.190608] usb usb3: Product: USB/IP Virtual Host Controller
[    0.190614] usb usb3: Manufacturer: Linux 4.19.0-socfpga-r1 vhci_hcd
[    0.190619] usb usb3: SerialNumber: vhci_hcd.0
[    0.191112] hub 3-0:1.0: USB hub found
[    0.191161] hub 3-0:1.0: 8 ports detected
[    0.192359] usbcore: registered new device driver usbip-host
[    0.192560] mousedev: PS/2 mouse device common for all mice
[    0.192657] usbcore: registered new interface driver appletouch
[    0.192721] usbcore: registered new interface driver bcm5974
[    0.192774] usbcore: registered new interface driver synaptics_usb
[    0.192819] usbcore: registered new interface driver iforce
[    0.193123] usbcore: registered new interface driver xpad
[    0.193554] i2c /dev entries driver
[    0.195466] Synopsys Designware Multimedia Card Interface Driver
[    0.195907] dw_mmc ff704000.dwmmc0: IDMAC supports 32-bit address mode.
[    0.195955] dw_mmc ff704000.dwmmc0: Using internal DMA controller.
[    0.195967] dw_mmc ff704000.dwmmc0: Version ID is 240a
[    0.196022] dw_mmc ff704000.dwmmc0: DW MMC controller at irq 32,32 bit host data width,1024 deep fifo
[    0.196123] dw_mmc ff704000.dwmmc0: Linked as a consumer to regulator.1
[    0.196319] mmc_host mmc0: card is polling.
[    0.208289] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    0.220962] hidraw: raw HID events driver (C) Jiri Kosina
[    0.227217] usbcore: registered new interface driver usbhid
[    0.227224] usbhid: USB HID core driver
[    0.227596] fpga_manager fpga0: Altera SOCFPGA FPGA Manager registered
[    0.228201] altera_hps2fpga_bridge ff400000.fpga_bridge: fpga bridge [lwhps2fpga] registered
[    0.228552] altera_hps2fpga_bridge ff500000.fpga_bridge: fpga bridge [hps2fpga] registered
[    0.235041] MrAudio: CMA addr = 0x1E880000
[    0.248657] MrAudio Audio buffer '/dev/MrAudio' created.
               Class --> 'MrAudio_sys'
               Major --> 257949696
[    0.248944] usbcore: registered new interface driver snd-usb-audio
[    0.249232] oprofile: using arm/armv7-ca9
[    0.250039] NET: Registered protocol family 17
[    0.250062] NET: Registered protocol family 15
[    0.250067] 8021q: 802.1Q VLAN Support v1.8
[    0.250095] lib80211: common routines for IEEE802.11 drivers
[    0.250100] lib80211_crypt: registered algorithm 'NULL'
[    0.250124] Key type dns_resolver registered
[    0.250469] ThumbEE CPU extension supported.
[    0.250483] Registering SWP/SWPB emulation handler
[    0.251852] Loading compiled-in X.509 certificates
[    0.252484] Key type encrypted registered
[    0.258711] rtc-m41t80 1-0068: registered as rtc0
[    0.259321] rtc-ds1307: probe of 1-006f failed with error -5
[    0.259361] i2c-gpio i2c_gpio: using lines 2012 (SDA) and 2013 (SCL)
[    0.260477] of_cfs_init
[    0.260543] of_cfs_init: OK
[    0.260754] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    0.264049] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    0.264107] ALSA device list:
[    0.264112]   #0: Dummy 1
[    0.264253] ttyS0 - failed to request DMA
[    0.264357] Waiting for root device /dev/mmcblk0p1...
[    0.264478] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    0.264485] cfg80211: failed to load regulatory.db
[    0.316883] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    0.316943] mmc0: new high speed SDXC card at address aaaa
[    0.317883] mmcblk0: mmc0:aaaa SC200 183 GiB
[    0.320626]  mmcblk0: p1 p2
[    0.327983] [EXFAT] trying to mount...
[    0.377100] random: fast init done
[    0.559292] usb 1-1: new high-speed USB device number 2 using dwc2
[    0.560104] [EXFAT] mounted successfully
[    0.606226] EXT4-fs (loop8): mounted filesystem with ordered data mode. Opts: (null)
[    0.606298] VFS: Mounted root (ext4 filesystem) readonly on device 7:128.
[    0.615021] devtmpfs: mounted
[    0.617844] Freeing unused kernel memory: 1024K
[    0.618157] Run /sbin/init as init process
[    0.738603] usb 1-1: New USB device found, idVendor=214b, idProduct=7000, bcdDevice= 1.00
[    0.738615] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    0.738621] usb 1-1: Product: USB2.0 HUB
[    0.739182] hub 1-1:1.0: USB hub found
[    0.739365] hub 1-1:1.0: 4 ports detected
[    2.434258] udevd[1140]: starting version 3.2.1
[    2.442848] random: udevd: uninitialized urandom read (16 bytes read)
[    2.445149] random: udevd: uninitialized urandom read (16 bytes read)
[    2.445239] random: udevd: uninitialized urandom read (16 bytes read)
[    2.499611] udevd[1141]: starting eudev-3.2.1
[    3.676287] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.738343] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    4.304781] print_req_error: I/O error, dev mmcblk0, sector 2304
[    4.655621] print_req_error: I/O error, dev mmcblk0, sector 2305
[    5.004433] print_req_error: I/O error, dev mmcblk0, sector 2306
[    5.353242] print_req_error: I/O error, dev mmcblk0, sector 2307
[    5.702047] print_req_error: I/O error, dev mmcblk0, sector 2308
[    6.050859] print_req_error: I/O error, dev mmcblk0, sector 2309
[    6.399669] print_req_error: I/O error, dev mmcblk0, sector 2310
[    6.748492] print_req_error: I/O error, dev mmcblk0, sector 2311
[    7.097324] print_req_error: I/O error, dev mmcblk0, sector 2312
[    7.446106] print_req_error: I/O error, dev mmcblk0, sector 2313
[    9.473011] print_req_error: 5 callbacks suppressed
[    9.473018] print_req_error: I/O error, dev mmcblk0, sector 2319
[    9.814664] print_req_error: I/O error, dev mmcblk0, sector 2320
[   10.156322] print_req_error: I/O error, dev mmcblk0, sector 2321
[   10.497963] print_req_error: I/O error, dev mmcblk0, sector 2322
[   10.839588] print_req_error: I/O error, dev mmcblk0, sector 2323
[   11.181210] print_req_error: I/O error, dev mmcblk0, sector 2324
[   11.522833] print_req_error: I/O error, dev mmcblk0, sector 2325
[   11.864453] print_req_error: I/O error, dev mmcblk0, sector 2326
[   12.206073] print_req_error: I/O error, dev mmcblk0, sector 2327
[   12.547694] print_req_error: I/O error, dev mmcblk0, sector 2328
[   14.567416] print_req_error: 5 callbacks suppressed
[   14.567423] print_req_error: I/O error, dev mmcblk0, sector 2334
[   14.909066] print_req_error: I/O error, dev mmcblk0, sector 2335
[   15.272343] print_req_error: I/O error, dev mmcblk0, sector 2337
[   15.613970] print_req_error: I/O error, dev mmcblk0, sector 2338
[   15.955592] print_req_error: I/O error, dev mmcblk0, sector 2339
[   16.297232] print_req_error: I/O error, dev mmcblk0, sector 2340
[   16.638892] print_req_error: I/O error, dev mmcblk0, sector 2341
[   16.980520] print_req_error: I/O error, dev mmcblk0, sector 2342
[   17.322140] print_req_error: I/O error, dev mmcblk0, sector 2343
[   17.663762] print_req_error: I/O error, dev mmcblk0, sector 2344
[   19.683470] print_req_error: 5 callbacks suppressed
[   19.683477] print_req_error: I/O error, dev mmcblk0, sector 2350
[   20.025129] print_req_error: I/O error, dev mmcblk0, sector 2351
[   20.366755] print_req_error: I/O error, dev mmcblk0, sector 2352
[   20.708376] print_req_error: I/O error, dev mmcblk0, sector 2353
[   21.049997] print_req_error: I/O error, dev mmcblk0, sector 2354
[   21.391620] print_req_error: I/O error, dev mmcblk0, sector 2355
[   21.733244] print_req_error: I/O error, dev mmcblk0, sector 2356
[   22.074878] print_req_error: I/O error, dev mmcblk0, sector 2357
[   22.416498] print_req_error: I/O error, dev mmcblk0, sector 2358
[   22.758138] print_req_error: I/O error, dev mmcblk0, sector 2359
[   25.480290] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[   25.542726] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   25.878418] print_req_error: 5 callbacks suppressed
[   25.878424] print_req_error: I/O error, dev mmcblk0, sector 2304
[   25.884450] Buffer I/O error on dev mmcblk0p1, logical block 256, async page read
[   26.227546] print_req_error: I/O error, dev mmcblk0, sector 2305
[   26.233550] Buffer I/O error on dev mmcblk0p1, logical block 257, async page read
[   26.576650] print_req_error: I/O error, dev mmcblk0, sector 2306
[   26.582655] Buffer I/O error on dev mmcblk0p1, logical block 258, async page read
[   26.925755] print_req_error: I/O error, dev mmcblk0, sector 2307
[   26.931765] Buffer I/O error on dev mmcblk0p1, logical block 259, async page read
[   27.274872] print_req_error: I/O error, dev mmcblk0, sector 2308
[   27.280874] Buffer I/O error on dev mmcblk0p1, logical block 260, async page read
[   27.623971] print_req_error: I/O error, dev mmcblk0, sector 2309
[   27.629975] Buffer I/O error on dev mmcblk0p1, logical block 261, async page read
[   27.973067] print_req_error: I/O error, dev mmcblk0, sector 2310
[   27.979070] Buffer I/O error on dev mmcblk0p1, logical block 262, async page read
[   28.322162] print_req_error: I/O error, dev mmcblk0, sector 2311
[   28.328165] Buffer I/O error on dev mmcblk0p1, logical block 263, async page read
[   29.028305] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[   29.090707] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   29.426381] print_req_error: I/O error, dev mmcblk0, sector 2304
[   29.432390] Buffer I/O error on dev mmcblk0p1, logical block 256, async page read
[   29.775524] print_req_error: I/O error, dev mmcblk0, sector 2305
[   29.781537] Buffer I/O error on dev mmcblk0p1, logical block 257, async page read
[   30.748292] usb 1-1.3: new high-speed USB device number 3 using dwc2
[   30.797561] random: crng init done
[   30.797569] random: 1 urandom warning(s) missed due to ratelimiting
[   30.835659] usb 1-1.3: New USB device found, idVendor=148f, idProduct=7601, bcdDevice= 0.00
[   30.835670] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   30.835677] usb 1-1.3: Product: 802.11 n WLAN
[   30.835683] usb 1-1.3: Manufacturer: MediaTek
[   30.835688] usb 1-1.3: SerialNumber: 1.0
[   30.900295] usb 1-1.3: reset high-speed USB device number 3 using dwc2
[   30.979339] mt7601u 1-1.3:1.0: ASIC revision: 76010001 MAC revision: 76010500
[   31.131552] print_req_error: 3 callbacks suppressed
[   31.131559] print_req_error: I/O error, dev mmcblk0, sector 2309
[   31.137579] buffer_io_error: 3 callbacks suppressed
[   31.137586] Buffer I/O error on dev mmcblk0p1, logical block 261, async page read
[   31.480686] print_req_error: I/O error, dev mmcblk0, sector 2310
[   31.486689] Buffer I/O error on dev mmcblk0p1, logical block 262, async page read
[   31.829790] print_req_error: I/O error, dev mmcblk0, sector 2311
[   31.835793] Buffer I/O error on dev mmcblk0p1, logical block 263, async page read
[   31.877363] mt7601u 1-1.3:1.0: Direct firmware load for mt7601u.bin failed with error -2
[   31.878197] mt7601u: probe of 1-1.3:1.0 failed with error -2
[   31.944370] usb 1-1.4: new full-speed USB device number 4 using dwc2
[   32.022159] usb 1-1.4: New USB device found, idVendor=057e, idProduct=2009, bcdDevice= 2.00
[   32.022171] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   32.022178] usb 1-1.4: Product: Pro Controller
[   32.022184] usb 1-1.4: Manufacturer: Nintendo Co., Ltd.
[   32.022189] usb 1-1.4: SerialNumber: 000000000001
[   32.026683] input: Nintendo Co., Ltd. Pro Controller as /devices/platform/soc/ffb40000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:057E:2009.0001/input/input0
[   32.029074] hid-generic 0003:057E:2009.0001: input,hidraw0: USB HID v1.11 Joystick [Nintendo Co., Ltd. Pro Controller] on usb-ffb40000.usb-1.4/input0
[   32.733845] usb 1-1.4: USB disconnect, device number 4
[   32.754887] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[   32.767312] socfpga-dwmac ff702000.ethernet eth0: No Safety Features support found
[   32.767329] socfpga-dwmac ff702000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[   32.767594] socfpga-dwmac ff702000.ethernet eth0: registered PTP clock
[   32.920331] usb 1-1.4: new full-speed USB device number 5 using dwc2
[   32.998544] usb 1-1.4: New USB device found, idVendor=045e, idProduct=028e, bcdDevice= 1.20
[   32.998556] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   32.998562] usb 1-1.4: Product: 8Bitdo Receiver
[   32.998568] usb 1-1.4: Manufacturer: 8Bitdo Receiver
[   32.998574] usb 1-1.4: SerialNumber: Receiver
[   33.000638] input: Microsoft X-Box 360 pad as /devices/platform/soc/ffb40000.usb/usb1/1-1/1-1.4/1-1.4:1.0/input/input1
[   36.899242] socfpga-dwmac ff702000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[  503.290699] EXT4-fs (loop8): re-mounted. Opts: (null)
# ^C
# [   30.835670] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
-sh: [: missing `]'
# [   30.835677] usb 1-1.3: Product: 802.11 n WLAN
-sh: [: missing `]'
# [   30.835683] usb 1-1.3: Manufacturer: MediaTek
-sh: [: missing `]'
# [   30.835688] usb 1-1.3: SerialNumber: 1.0
-sh: [: missing `]'
# [   30.900295] usb 1-1.3: reset high-speed USB device number 3 using dwc2
-sh: [: missing `]'
# [   30.979339] mt7601u 1-1.3:1.0: ASIC revision: 76010001 MAC revision: 76010500
-sh: [: missing `]'
# [   31.131552] print_req_error: 3 callbacks suppressed
-sh: [: missing `]'
# [   31.131559] print_req_error: I/O error, dev mmcblk0, sector 2309
-sh: [: missing `]'
# [   31.137579] buffer_io_error: 3 callbacks suppressed
-sh: [: missing `]'
# [   31.137586] Buffer I/O error on dev mmcblk0p1, logical block 261, async page read
-sh: [: missing `]'
# [   31.480686] print_req_error: I/O error, dev mmcblk0, sector 2310
-sh: [: missing `]'
# [   31.486689] Buffer I/O error on dev mmcblk0p1, logical block 262, async page read
-sh: [: missing `]'
# [   31.829790] print_req_error: I/O error, dev mmcblk0, sector 2311
-sh: [: missing `]'
# [   31.835793] Buffer I/O error on dev mmcblk0p1, logical block 263, async page read
-sh: [: missing `]'
# [   31.877363] mt7601u 1-1.3:1.0: Direct firmware load for mt7601u.bin failed with error -2
-sh: [: missing `]'
# [   31.878197] mt7601u: probe of 1-1.3:1.0 failed with error -2
-sh: [: missing `]'
# [   31.944370] usb 1-1.4: new full-speed USB device number 4 using dwc2
-sh: [: missing `]'
# [   32.022159] usb 1-1.4: New USB device found, idVendor=057e, idProduct=2009, bcdDevice= 2.00
-sh: [: missing `]'
# [   32.022171] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
-sh: [: missing `]'
# [   32.022178] usb 1-1.4: Product: Pro Controller
-sh: [: missing `]'
# [   32.022184] usb 1-1.4: Manufacturer: Nintendo Co., Ltd.
-sh: [: missing `]'
# [   32.022189] usb 1-1.4: SerialNumber: 000000000001
-sh: [: missing `]'
# [   32.026683] input: Nintendo Co., Ltd. Pro Controller as /devices/platform/soc/ffb40000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:057E:2009.0001/input/input0
-sh: [: missing `]'
# [   32.029074] hid-generic 0003:057E:2009.0001: input,hidraw0: USB HID v1.11 Joystick [Nintendo Co., Ltd. Pro Controller] on usb-ffb40000.usb-1.4/input0
-sh: [: missing `]'
# [   32.733845] usb 1-1.4: USB disconnect, device number 4
-sh: [: missing `]'
# [   32.754887] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
-sh: syntax error near unexpected token `('
# [   32.767312] socfpga-dwmac ff702000.ethernet eth0: No Safety Features support found
-sh: [: missing `]'
# [   32.767329] socfpga-dwmac ff702000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
-sh: [: missing `]'
# [   32.767594] socfpga-dwmac ff702000.ethernet eth0: registered PTP clock
-sh: [: missing `]'
# [   32.920331] usb 1-1.4: new full-speed USB device number 5 using dwc2
-sh: [: missing `]'
# [   32.998544] usb 1-1.4: New USB device found, idVendor=045e, idProduct=028e, bcdDevice= 1.20
-sh: [: missing `]'
# [   32.998556] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
-sh: [: missing `]'
# [   32.998562] usb 1-1.4: Product: 8Bitdo Receiver
-sh: [: missing `]'
# [   32.998568] usb 1-1.4: Manufacturer: 8Bitdo Receiver
-sh: [: missing `]'
# [   32.998574] usb 1-1.4: SerialNumber: Receiver
-sh: [: missing `]'
# [   33.000638] input: Microsoft X-Box 360 pad as /devices/platform/soc/ffb40000.usb/usb1/1-1/1-1.4/1-1.4:1.0/input/input1
-sh: [: missing `]'
# [   36.899242] socfpga-dwmac ff702000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
-sh: [: missing `]'
# [  503.290699] EXT4-fs (loop8): re-mounted. Opts: (null)
-sh: syntax error near unexpected token `('

I used the mt7601u.bin in lib\firmware
Is there a workaround?

[Sorgelig]

This is my Log:

cannot tell about the dongle (i don't recommend mediatek devices), but you have problem with SD card:

Code: Select all

Buffer I/O error on dev mmcblk0p1

[lavatar]

This is my Log:

cannot tell about the dongle (i don't recommend mediatek devices), but you have problem with SD card:

Code: Select all

Buffer I/O error on dev mmcblk0p1

Thx for responding, i try to reformat the sd card and start completly fresh.

[lavatar]

This is my Log:

cannot tell about the dongle (i don't recommend mediatek devices), but you have problem with SD card:

Code: Select all

Buffer I/O error on dev mmcblk0p1

Thx, it worked!

[lavatar]

The Update Process over wifi works but i have the problem that it is very slow.
It needs for one single check, downloading approximately about 3 Minutes.

Anybody with the same Problem?

[knc]

The Update Process over wifi works but i have the problem that it is very slow.
It needs for one single check, downloading approximately about 3 Minutes.

Anybody with the same Problem?

i had the same with a Realtek RTL8192cu wifi dongle until the linux update on feb 6th and since then its been working fine
so if you are not on the latest sd installer try running that again to update the linux

[lavatar]

The Update Process over wifi works but i have the problem that it is very slow.
It needs for one single check, downloading approximately about 3 Minutes.

Anybody with the same Problem?

i had the same with a Realtek RTL8192cu wifi dongle until the linux update on feb 6th and since then its been working fine
so if you are not on the latest sd installer try running that again to update the linux

Im on the latest sd installer, because the sd card was corrupted.
Hopefully this will fixed in the near future, thank you!

[lavatar]

Meanwhile i updated the complete Mister but no improvment about the speed for a checking/download-process.

Code: Select all

[    0.187285] hub 3-0:1.0: USB hub found
[    0.187337] hub 3-0:1.0: 8 ports detected
[    0.188448] usbcore: registered new device driver usbip-host
[    0.188697] mousedev: PS/2 mouse device common for all mice
[    0.188807] usbcore: registered new interface driver appletouch
[    0.188887] usbcore: registered new interface driver bcm5974
[    0.188960] usbcore: registered new interface driver synaptics_usb
[    0.189027] usbcore: registered new interface driver iforce
[    0.189445] usbcore: registered new interface driver xpad
[    0.189927] i2c /dev entries driver
[    0.191206] Synopsys Designware Multimedia Card Interface Driver
[    0.192063] dw_mmc ff704000.dwmmc0: IDMAC supports 32-bit address mode.
[    0.192110] dw_mmc ff704000.dwmmc0: Using internal DMA controller.
[    0.192122] dw_mmc ff704000.dwmmc0: Version ID is 240a
[    0.192181] dw_mmc ff704000.dwmmc0: DW MMC controller at irq 32,32 bit host data width,1024 deep fifo
[    0.192276] dw_mmc ff704000.dwmmc0: Linked as a consumer to regulator.1
[    0.192416] mmc_host mmc0: card is polling.
[    0.204520] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    0.217157] hidraw: raw HID events driver (C) Jiri Kosina
[    0.223654] usbcore: registered new interface driver usbhid
[    0.223661] usbhid: USB HID core driver
[    0.223979] fpga_manager fpga0: Altera SOCFPGA FPGA Manager registered
[    0.224662] altera_hps2fpga_bridge ff400000.fpga_bridge: fpga bridge [lwhps2fpga] registered
[    0.224963] altera_hps2fpga_bridge ff500000.fpga_bridge: fpga bridge [hps2fpga] registered
[    0.231414] MrAudio: CMA addr = 0x1E880000
[    0.245684] MrAudio Audio buffer '/dev/MrAudio' created.
               Class --> 'MrAudio_sys'
               Major --> 257949696
[    0.245893] usbcore: registered new interface driver snd-usb-audio
[    0.246155] oprofile: using arm/armv7-ca9
[    0.247031] NET: Registered protocol family 17
[    0.247059] NET: Registered protocol family 15
[    0.247066] 8021q: 802.1Q VLAN Support v1.8
[    0.247090] lib80211: common routines for IEEE802.11 drivers
[    0.247096] lib80211_crypt: registered algorithm 'NULL'
[    0.247117] Key type dns_resolver registered
[    0.247386] ThumbEE CPU extension supported.
[    0.247398] Registering SWP/SWPB emulation handler
[    0.248786] Loading compiled-in X.509 certificates
[    0.249354] Key type encrypted registered
[    0.255488] rtc-m41t80 1-0068: registered as rtc0
[    0.256124] rtc-ds1307: probe of 1-006f failed with error -5
[    0.256163] i2c-gpio i2c_gpio: using lines 2012 (SDA) and 2013 (SCL)
[    0.257297] rtc-m41t80 1-0068: setting system clock to 2019-03-04 19:27:05 UTC (1551727625)
[    0.257306] of_cfs_init
[    0.257372] of_cfs_init: OK
[    0.257615] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    0.261127] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    0.261195] ALSA device list:
[    0.261200]   #0: Dummy 1
[    0.261348] ttyS0 - failed to request DMA
[    0.261432] Waiting for root device /dev/mmcblk0p1...
[    0.261579] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    0.261587] cfg80211: failed to load regulatory.db
[    0.306232] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    0.306291] mmc0: new high speed SDXC card at address aaaa
[    0.307201] mmcblk0: mmc0:aaaa SC200 183 GiB
[    0.310099]  mmcblk0: p1 p2
[    0.317179] [EXFAT] trying to mount...
[    0.351538] random: fast init done
[    0.439046] [EXFAT] mounted successfully
[    0.461208] EXT4-fs (loop8): mounted filesystem with ordered data mode. Opts: (null)
[    0.461253] VFS: Mounted root (ext4 filesystem) readonly on device 7:128.
[    0.465073] devtmpfs: mounted
[    0.467885] Freeing unused kernel memory: 1024K
[    0.468207] Run /sbin/init as init process
[    0.559532] usb 1-1: new high-speed USB device number 2 using dwc2
[    0.738842] usb 1-1: New USB device found, idVendor=214b, idProduct=7000, bcdDevice= 1.00
[    0.738853] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    0.738860] usb 1-1: Product: USB2.0 HUB
[    0.739392] hub 1-1:1.0: USB hub found
[    0.739532] hub 1-1:1.0: 4 ports detected
[    1.322834] udevd[1142]: starting version 3.2.1
[    1.337643] random: udevd: uninitialized urandom read (16 bytes read)
[    1.339092] random: udevd: uninitialized urandom read (16 bytes read)
[    1.339183] random: udevd: uninitialized urandom read (16 bytes read)
[    1.371224] udevd[1144]: starting eudev-3.2.1
[    2.506529] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.568544] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    2.943983] print_req_error: I/O error, dev mmcblk0, sector 2304
[    3.285611] print_req_error: I/O error, dev mmcblk0, sector 2305
[    3.426095] urandom_read: 2 callbacks suppressed
[    3.426102] random: udevd: uninitialized urandom read (16 bytes read)
[    3.426240] random: udevd: uninitialized urandom read (16 bytes read)
[    3.627270] print_req_error: I/O error, dev mmcblk0, sector 2306
[    3.968929] print_req_error: I/O error, dev mmcblk0, sector 2307
[    4.310575] print_req_error: I/O error, dev mmcblk0, sector 2308
[    4.652214] print_req_error: I/O error, dev mmcblk0, sector 2309
[    4.993859] print_req_error: I/O error, dev mmcblk0, sector 2310
[    5.335509] print_req_error: I/O error, dev mmcblk0, sector 2311
[    5.677142] print_req_error: I/O error, dev mmcblk0, sector 2312
[    6.018783] print_req_error: I/O error, dev mmcblk0, sector 2313
[    8.038616] print_req_error: 5 callbacks suppressed
[    8.038624] print_req_error: I/O error, dev mmcblk0, sector 2319
[    8.380288] print_req_error: I/O error, dev mmcblk0, sector 2320
[    8.721929] print_req_error: I/O error, dev mmcblk0, sector 2321
[    9.063559] print_req_error: I/O error, dev mmcblk0, sector 2322
[    9.405195] print_req_error: I/O error, dev mmcblk0, sector 2323
[    9.746835] print_req_error: I/O error, dev mmcblk0, sector 2324
[   10.088492] print_req_error: I/O error, dev mmcblk0, sector 2325
[   10.430154] print_req_error: I/O error, dev mmcblk0, sector 2326
[   10.771793] print_req_error: I/O error, dev mmcblk0, sector 2327
[   11.113440] print_req_error: I/O error, dev mmcblk0, sector 2328
[   13.133258] print_req_error: 5 callbacks suppressed
[   13.133265] print_req_error: I/O error, dev mmcblk0, sector 2334
[   13.474939] print_req_error: I/O error, dev mmcblk0, sector 2335
[   13.816580] print_req_error: I/O error, dev mmcblk0, sector 2336
[   14.158218] print_req_error: I/O error, dev mmcblk0, sector 2337
[   14.499864] print_req_error: I/O error, dev mmcblk0, sector 2338
[   14.841510] print_req_error: I/O error, dev mmcblk0, sector 2339
[   15.183150] print_req_error: I/O error, dev mmcblk0, sector 2340
[   15.524796] print_req_error: I/O error, dev mmcblk0, sector 2341
[   15.866439] print_req_error: I/O error, dev mmcblk0, sector 2342
[   16.208074] print_req_error: I/O error, dev mmcblk0, sector 2343
[   18.227885] print_req_error: 5 callbacks suppressed
[   18.227892] print_req_error: I/O error, dev mmcblk0, sector 2349
[   18.569569] print_req_error: I/O error, dev mmcblk0, sector 2350
[   18.911221] print_req_error: I/O error, dev mmcblk0, sector 2351
[   19.252869] print_req_error: I/O error, dev mmcblk0, sector 2352
[   19.594537] print_req_error: I/O error, dev mmcblk0, sector 2353
[   19.936176] print_req_error: I/O error, dev mmcblk0, sector 2354
[   20.277816] print_req_error: I/O error, dev mmcblk0, sector 2355
[   20.619454] print_req_error: I/O error, dev mmcblk0, sector 2356
[   20.961085] print_req_error: I/O error, dev mmcblk0, sector 2357
[   21.302752] print_req_error: I/O error, dev mmcblk0, sector 2358
[   23.322537] print_req_error: 5 callbacks suppressed
[   23.322545] print_req_error: I/O error, dev mmcblk0, sector 2364
[   23.664205] print_req_error: I/O error, dev mmcblk0, sector 2365
[   24.005843] print_req_error: I/O error, dev mmcblk0, sector 2366
[   24.347487] print_req_error: I/O error, dev mmcblk0, sector 2367
[   25.134531] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[   25.196564] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   25.532270] print_req_error: I/O error, dev mmcblk0, sector 2304
[   25.538286] Buffer I/O error on dev mmcblk0p1, logical block 256, async page read
[   25.881417] print_req_error: I/O error, dev mmcblk0, sector 2305
[   25.887436] Buffer I/O error on dev mmcblk0p1, logical block 257, async page read
[   26.230565] print_req_error: I/O error, dev mmcblk0, sector 2306
[   26.236575] Buffer I/O error on dev mmcblk0p1, logical block 258, async page read
[   26.579707] print_req_error: I/O error, dev mmcblk0, sector 2307
[   26.585724] Buffer I/O error on dev mmcblk0p1, logical block 259, async page read
[   26.928850] print_req_error: I/O error, dev mmcblk0, sector 2308
[   26.934862] Buffer I/O error on dev mmcblk0p1, logical block 260, async page read
[   27.277978] print_req_error: I/O error, dev mmcblk0, sector 2309
[   27.283987] Buffer I/O error on dev mmcblk0p1, logical block 261, async page read
[   27.627110] Buffer I/O error on dev mmcblk0p1, logical block 262, async page read
[   27.970224] Buffer I/O error on dev mmcblk0p1, logical block 263, async page read
[   28.680529] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[   28.742940] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[   29.078645] print_req_error: 2 callbacks suppressed
[   29.078652] print_req_error: I/O error, dev mmcblk0, sector 2304
[   29.084677] Buffer I/O error on dev mmcblk0p1, logical block 256, async page read
[   29.427797] print_req_error: I/O error, dev mmcblk0, sector 2305
[   29.433811] Buffer I/O error on dev mmcblk0p1, logical block 257, async page read
[   29.776933] print_req_error: I/O error, dev mmcblk0, sector 2306
[   30.118581] print_req_error: I/O error, dev mmcblk0, sector 2307
[   30.460229] print_req_error: I/O error, dev mmcblk0, sector 2308
[   30.796523] usb 1-1.3: new high-speed USB device number 3 using dwc2
[   30.801876] print_req_error: I/O error, dev mmcblk0, sector 2309
[   30.807900] buffer_io_error: 3 callbacks suppressed
[   30.807906] Buffer I/O error on dev mmcblk0p1, logical block 261, async page read
[   30.890892] usb 1-1.3: New USB device found, idVendor=148f, idProduct=7601, bcdDevice= 0.00
[   30.890903] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   30.890910] usb 1-1.3: Product: 802.11 n WLAN
[   30.890917] usb 1-1.3: Manufacturer: MediaTek
[   30.890923] usb 1-1.3: SerialNumber: 1.0
[   30.956526] usb 1-1.3: reset high-speed USB device number 3 using dwc2
[   31.035571] mt7601u 1-1.3:1.0: ASIC revision: 76010001 MAC revision: 76010500
[   31.151052] print_req_error: I/O error, dev mmcblk0, sector 2310
[   31.157073] Buffer I/O error on dev mmcblk0p1, logical block 262, async page read
[   31.379048] random: crng init done
[   31.500207] print_req_error: I/O error, dev mmcblk0, sector 2311
[   31.506245] Buffer I/O error on dev mmcblk0p1, logical block 263, async page read
[   31.550613] mt7601u 1-1.3:1.0: Firmware Version: 0.1.00 Build: 7640 Build time: 201302052146____
[   31.928106] mt7601u 1-1.3:1.0: Warning: unsupported EEPROM version 0d
[   31.928117] mt7601u 1-1.3:1.0: EEPROM ver:0d fae:00
[   32.146773] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   32.217582] usb 1-1.4: new full-speed USB device number 4 using dwc2
[   32.296373] usb 1-1.4: New USB device found, idVendor=057e, idProduct=2009, bcdDevice= 2.00
[   32.296403] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   32.296421] usb 1-1.4: Product: Pro Controller
[   32.296439] usb 1-1.4: Manufacturer: Nintendo Co., Ltd.
[   32.296448] usb 1-1.4: SerialNumber: 000000000001
[   32.302430] input: Nintendo Co., Ltd. Pro Controller as /devices/platform/soc/ffb40000.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:057E:2009.0001/input/input0
[   32.303544] hid-generic 0003:057E:2009.0001: input,hidraw0: USB HID v1.11 Joystick [Nintendo Co., Ltd. Pro Controller] on usb-ffb40000.usb-1.4/input0
[   32.342532] Micrel KSZ9031 Gigabit PHY stmmac-0:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=stmmac-0:01, irq=POLL)
[   32.345239] socfpga-dwmac ff702000.ethernet eth0: No Safety Features support found
[   32.345826] socfpga-dwmac ff702000.ethernet eth0: registered PTP clock
[   33.037834] usb 1-1.4: USB disconnect, device number 4
[   33.223530] usb 1-1.4: new full-speed USB device number 5 using dwc2
[   33.301936] usb 1-1.4: New USB device found, idVendor=045e, idProduct=028e, bcdDevice= 1.20
[   33.301947] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   33.301954] usb 1-1.4: Product: 8Bitdo Receiver
[   33.301961] usb 1-1.4: Manufacturer: 8Bitdo Receiver
[   33.301967] usb 1-1.4: SerialNumber: Receiver
[   33.304636] input: Microsoft X-Box 360 pad as /devices/platform/soc/ffb40000.usb/usb1/1-1/1-1.4/1-1.4:1.0/input/input1
[   34.130342] wlan0: authenticate with 44:4e:6d:87:96:d6
[   34.151254] wlan0: send auth to 44:4e:6d:87:96:d6 (try 1/3)
[   34.352540] wlan0: send auth to 44:4e:6d:87:96:d6 (try 2/3)
[   34.358727] wlan0: authenticated
[   34.359729] wlan0: associate with 44:4e:6d:87:96:d6 (try 1/3)
[   34.371734] wlan0: RX AssocResp from 44:4e:6d:87:96:d6 (capab=0x1431 status=0 aid=3)
[   34.384213] wlan0: associated
[   34.632538] wlan0: Limiting TX power to 20 (20 - 0) dBm as advertised by 44:4e:6d:87:96:d6
[  142.268275] EXT4-fs (loop8): re-mounted. Opts: (null)
[  600.610372] EXT4-fs (loop8): re-mounted. Opts: (null)
#

Is there a other problem with my system? The usb hub maybe is responsable?

[warham]

Meanwhile i updated the complete Mister but no improvment about the speed for a checking/download-process.

Code: Select all

#

Is there a other problem with my system? The usb hub maybe is responsable?

Yes, Linux/usb hub combination. try all the different usb slots.

[lavatar]

Meanwhile i updated the complete Mister but no improvment about the speed for a checking/download-process.

Code: Select all

#

Is there a other problem with my system? The usb hub maybe is responsable?

Yes, Linux/usb hub combination. try all the different usb slots.

Wow, thx! The Solution was, indeed, to change the Device in other slots!

[Newsdee]

Did something change in the last Linux release?
My dongle was working but after I've ran the latest update, it's no longer recognized.

[Sorgelig]

Did something change in the last Linux release?
My dongle was working but after I've ran the latest update, it's no longer recognized.

it depends what version you've used before. I didn't change USB code many months.

[Newsdee]

I think it was the powered hub (or lack thereof). It has been stable after I gave it juice.
I'm not sure why it worked before, but I suppose it was a fluke.

In any case it isn't driver related, happy I got two of these WiFi dongles from AliExpress.

[kinox51]

Hey,

for those who have problems with the update script updating slowly over wifi:
I'm using an EDIMAX EN-7811Un wifi dongle (which has been automaticly been recognized) and two 8Bitdo PS Classic receivers on a 7-port usb hub.

When both of the 8Bitdo receivers were plugged in the wifi connects but the update process is extremly slow or even stopps working.
I first disconnected both receivers and the update works immediately after a quick restart of the mister.

Then I found out that with one receiver the update script also works, so the problem has to be with two of the same receivers plugged into the usb hub.

Hope this helps other people.

[arrowheadpancake]

I added the newer Edimax EW-7822ULC 5ghz (verified joins my 5ghz network successfully) to the MiSTer wiki. I added some USB IDs as well. I also added the somewhat unintuitive note about the newer DWA-171 hardware firmware revisions not working out of the box. I also added an example path /media/XXX for the supplicant file if you are coming from the host itself (via ethernet/ssh) versus the sd card.

https://github.com/MiSTer-devel/Main_Mi ... WiFi-setup

https://www.amazon.com/Edimax-Adapter-S ... B01MY7PL10

[Newsdee]

My wifi dongle seems to have stopped working, but I suspect it's faulty hardware as it was a cheap one and it is not recognized in the device list. Need to secure a new one...

[warham]

Hey,

for those who have problems with the update script updating slowly over wifi:
I'm using an EDIMAX EN-7811Un wifi dongle (which has been automaticly been recognized) and two 8Bitdo PS Classic receivers on a 7-port usb hub.

Hope this helps other people.

which hub are you using and what revision # is it?

[kinox51]

I’m using an modded 1.1 usb hub with a switch mod:

https://circuit-board.de/forum/index.ph ... humbnail=1

It’s a mod from a member of the circuit-board.de forum

[ericgus]

I just want to mention I too am seeing issues with my usb wifi dongle .. I had not used wifi in a bit but today when I tried its going VERY SLOWLY as others above described.. I checked dmesg and no I/O errors, tried switch USB hub ports etc.. still having a lot of latency .. I guess for now I can plug a network cable into it but wanted to throw my name into the "me too" list.. I even tried a second adaptor (they both use realtek chips that previously worked fine with no issues) .. For laughs I even tried getting the latest linux.img and zImage_dtb files (20190627 release) and copied/replaced them over to the SD card manually, no difference. Either adaptor will get an IP address but trying to remotely SSH in or SFTP it can lag up to 3 or so minutes before getting any sort of response and then when running things like the update script can be painfully slow .. it does eventually complete but I think it took well over an hour to finish (I walked away for a bit so I dont have an exact timing .. but it was orders of magnitude slower than usual)

edit:

Thought I would share some PING output .. just to show how random the network timeouts can vary.. (doing a ping to google.com)
{as I mentioned above, all this exact same hardware in the exact same configuration worked previously with the same usb dongle}

64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=316 ttl=54 time=9106 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=317 ttl=54 time=8082 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=318 ttl=54 time=7058 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=322 ttl=54 time=19.1 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=323 ttl=54 time=106 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=324 ttl=54 time=1154 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=325 ttl=54 time=107 ms
From 192.168.0.106 (192.168.0.106) icmp_seq=376 Destination Host Unreachable
From 192.168.0.106 (192.168.0.106) icmp_seq=377 Destination Host Unreachable
From 192.168.0.106 (192.168.0.106) icmp_seq=378 Destination Host Unreachable
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=326 ttl=54 time=56454 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=327 ttl=54 time=55405 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=328 ttl=54 time=54382 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=329 ttl=54 time=53358 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=330 ttl=54 time=52389 ms
64 bytes from lga25s56-in-f14.1e100.net (172.217.7.14): icmp_seq=331 ttl=54 time=51365 ms

[CmputrBlu]

Sorry if this has been answered but I'm pretty much stumped here and I suspect the issue is going to be something stupid and simple but I don't know. I have the Edimax EW-7811UN wireless which is suppose to work and I see has worked but others from the get go. From reading this forum and the wiki I have done a few things.

Ran command "lsusb" and got the correct hardware ID for the dongle, device 3

IMG_20191009_025555843.jpg

Ran command "dmesg" and it appears the dongle is being recognized and firmware loaded. I assume the correct firmware.

IMG_20191009_025513911.jpg

I figured that "wpa_supplicant.conf" gets run or read by the Mister upon boot so I typed the the file name and got a syntax error.

IMG_20191009_025658115.jpg

Is this my error and if so how do I fix it? I'm editing the file on the PC and FTPing it over to the Mister, but possible something is going wrong along the chain.

TIA

[Sorgelig]

wpa_supplicant.conf is not executable file.

[CmputrBlu]

OK. Then back to tracking down the issue. Thanks.

[warham]

OK. Then back to tracking down the issue. Thanks.

did you already edit that wpa file with your wifi name and password?

[CmputrBlu]

OK. Then back to tracking down the issue. Thanks.

did you already edit that wpa file with your wifi name and password?

Yes, but I don't see anything happen. For example I would expect the dongle to light up (at least the original Asus I tried has an LED inside which lights on the PC side) but nothing. It's not even trying to search for a network it seems. Is it possible there is something that I accidentally turned off running a script that needs to be on.