Atari-Forum

On Atari https://demozoo.org/productions/95702/
On pc nothing more simple than graoumf tracker itself afaik http://graoumftracker2.sourceforge.net

Ok so now I've tried and it's all good now it's just a matter off wrappin my mind around how it works so i wont get confused again thank you all!

@shoggoth; I may be out on thin ice here but if I add up the bits value in the first result (434 dec for st-low) it makes sense, if I discard the upper word it would equal 434-256 or am I totally wrong? Still wonder why i get different results from the first read when all i do is read :/ Ahem, and I...

Will try later when i get home, but if the upper word is dropped you'll miss the doubleline bit no? I've seen that the bits 2-8 (or 1-7 i dont know wich is the right way to count :)) are reserved so i guess that it is there the garbage is showing up.. Thanks anyhow, it"s not that important but it ma...

I just save the modecode to a variable the same way I've seen in all examples mode%=XBIOS(88,-1) Then i print the value to screen and first time i get the correct decimal value (434 if in st-low for example). I tried this too for i=0 to 10 mode%=(xbios(88,w:-1)) print mode% next i First one is actua...

Sorry for reviving an old thread but sort of on topic :? Shouldn't VsetMode (or xbios(88)) return the same value every time i inquire it (without changing the resolution of course) ? If i save it more than once, the second time and beyond it returns a value ten times a word?? (Second and on stays th...

catmando wrote: 3. The 1uF 50v CAP also by the reset switch had a +10 35v cap piggybacked alongside it, so I removed both and replaced them with a single new 1uf 50v

N00b question but just out of curiosity when there seems to be a problem with reset circuit, the piggyback CAP isn't necessary?

Just a thought

Hi! I've got some free samples of the Dallas 12887A from maxim, but I noticed there are fewer pins on these? Made me a bit insecure =).. Also, I've lended a solderstation from work to do the switch, because my own 15w iron does'nt get warm enough it seems. What temperature should I have? Regards /Da...

Probably a stupid question... but does anyone know if one of these

http://www.latticesemi.com/lit/docs/dat ... l/20v8.pdf

would be usable?

Tried to e-mail best electronics but no answer :/

***Update*** Got in touch with best, and ordered a chip! Problem solved...

Hi!

I'm looking for an falcon ic, located at U44 on the motherboard and marked C302834-001.

Cheers Daniel

Charles:

You could probably use Smurf (http://home.ewr-online.de/~gstoll/0a.htm) to convert to pi3 i think

Hello. I have also tried the above but eperimented with the resolution.
I can't really get why, if I set res to 640*480*8bp (&X111011)(VGA) I get the same image twice
and it looks smaller than the original 320*240.. Anyone got any ideas?

Wongck, thanks a lot! I finally got it to work but i did'nt solder, i just twisted the cable so pin 10 from the controller went to pin 12 on the fdd and vice versa and it works like a charm

Ok, I've got hold of an pc motherboard for the floppy interface, but there is a ground-pin(5) missing, does it matter?
I'm not too keen on soldering so I don't want to do something I will regret

Hi!

Have you got any c302096 left? Any idea of how much the shipping to Sweden would cost?

Hello! A couple of days ago I got my falcon out of the closet for the first time in a year. Started it and saw the nice logo and it performed a memorytest wich was fine,,.. then nothig. After have searched for hdd (without finding any though i had both one ide and one scsi+cd, it might have been bec...