Search found 11 matches

by subw00ter
Thu Apr 16, 2020 2:21 am
Forum: MiSTer
Topic: Bluetooth Pairing dialog always pops up
Replies: 5
Views: 772

Re: Bluetooth Pairing dialog always pops up

I have checked all GPIO pins, especially pins 12 & 13 on GPIO 1. There is no connection, no bending, no short. I have checked the DE10 onboard buttons, they are not being pressed. I press them manually and they will perform the proper action. These are the steps: 1. Use SD card utility to create SD ...
by subw00ter
Sun Apr 12, 2020 2:15 am
Forum: MiSTer
Topic: Bluetooth Pairing dialog always pops up
Replies: 5
Views: 772

Re: Bluetooth Pairing dialog always pops up

Sorgelig wrote:Either OSD button on I/O board is always pressed, or F11 on keyboard.
Thanks for your reply, Sorgelig. However, this happens with no I/O board installed and no keyboard plugged in. It happens on EVERY boot.

Are there settings that enable automatic BT pairing without manual input?
by subw00ter
Thu Apr 09, 2020 4:29 pm
Forum: MiSTer
Topic: Bluetooth Pairing dialog always pops up
Replies: 5
Views: 772

Bluetooth Pairing dialog always pops up

When I run the MiSTer updater script, it must be installing another script for BT pairing, or changing some setting. When I boot the MiSTER, and every time I load a core, it pops up with a BT Pairing dialog window that I must respond to. This often interrupts my menu selection or game browsing, and ...
by subw00ter
Tue Dec 10, 2019 5:06 am
Forum: MiSTer
Topic: Help with starting cores (no video output)
Replies: 26
Views: 7632

Re: Help with starting cores (no video output)

Good tip, DrOG. I think I had to do this for the firmware. I'll try the raw link on the cores and see if that works too.

Thanks everyone for your help, now I just have to wait for the RAM to come!
by subw00ter
Tue Dec 10, 2019 2:02 am
Forum: MiSTer
Topic: Help with starting cores (no video output)
Replies: 26
Views: 7632

Re: Help with starting cores (no video output)

NES requires SDRAM board. No idea what you are fishing there. Ah, sorry Sorgelig, I see that now. But, I was also trying Genesis and arcade cores and none were working. Try changing hdmi cable Thanks for the reply. I've tried 3 different HDMI cables. Again, HDMI works in Menu. Then all LEDs turn of...
by subw00ter
Mon Dec 09, 2019 2:55 pm
Forum: MiSTer
Topic: Help with starting cores (no video output)
Replies: 26
Views: 7632

Re: No HDMI signal when I load a core from menu.rbf

danytyler wrote: Try changing hdmi cable
Thanks for the reply. I've tried 3 different HDMI cables. Again, HDMI works in Menu. Then all LEDs turn off when i start a system core, except for the 3.3V led.
by subw00ter
Mon Dec 09, 2019 1:19 am
Forum: MiSTer
Topic: Help with starting cores (no video output)
Replies: 26
Views: 7632

Re: Help with starting cores (no video output)

Strange, retroturk and i have the same problem after setting up in the same week.
by subw00ter
Mon Dec 09, 2019 12:25 am
Forum: MiSTer
Topic: Help with starting cores (no video output)
Replies: 26
Views: 7632

No HDMI signal when I load a core from menu.rbf

I have set up my MiSTer according to the instructions exactly, everything goes fine with the SD Card utility, etc. I do not have a RAM board, nor an I/O board. I am just trying to test NES, Genesis, and a handful of Arcade cores. When I choose the NES or Genesis core from the menu, all LEDs on the b...
by subw00ter
Fri Dec 06, 2019 10:59 pm
Forum: MiSTer
Topic: Newbie questions
Replies: 690
Views: 189597

Re: Newbie questions

I can't get any cores to run except for menu.rbf. I get no HDMI signal when I select a core such as NES or Genesis. I have: -DE10 Nano -OEM PSU -OEM SD Card -Working USB keyboard -HDMI (I've tried 3 monitors, 2 TVs, and an A/V Receiver. All show MiSTer main menu but lose signal when I try a core) -N...
by subw00ter
Fri Dec 06, 2019 10:37 pm
Forum: MiSTer
Topic: Is my DE10-Nano Broken?
Replies: 31
Views: 12206

Re: Is my DE10-Nano Broken?

Is it not OK to use the PSU that comes with the DE10-Nano?
by subw00ter
Fri Dec 06, 2019 10:27 pm
Forum: MiSTer
Topic: Help with starting cores (no video output)
Replies: 26
Views: 7632

Re: Help with starting cores (no video output)

roc, Did you solve this? I am having the same problem: -DE10 Nano -OEM SD card -No RAM board, no I/O board -HDMI out I follow the exact directions on https://github.com/MiSTer-devel/Main_MiSTer/wiki/Setup-Guide I ran the SD Card Utility, everything goes fine. I can load the main menu.rbf and see a l...

Go to advanced search